Drilled, Reamed, or Bored: The Hole Process Sets the Tolerance

Read More Below

Crafting Excellence Through the Art of Precision Machining

FM Machine Co. excels in manufacturing precision machined parts, producing components with high accuracy and quality to meet the exacting standards of industries like aerospace, automotive, and medical devices. With advanced machining technology and a team of skilled engineers, FM Machine Co. can create complex prototypes for testing and validation, ensuring that each product meets customer specifications before full-scale production.

Tight Tolerance • Decades of Experience • Precision Machining: Get a Quote >

Hole tolerances are set by the process that finishes the hole, not by the number on the drawing alone. A drilled hole, a reamed hole, and a bored hole each hold a different level of size accuracy, straightness, and location, and each step up costs time. FM Machine Co. in Akron, Ohio wrote this guide for engineers and buyers who want to know what a hole tolerance will cost before they send a drawing.

A hole tolerance is the range a hole’s diameter is allowed to vary, between a maximum and a minimum size. The drawing states the range, and the process that finishes the hole decides whether the shop can hold it.

Most holes start with a drill. Standard drill sizes are the quick, accurate route, while nonstandard diameters need an extra machining step that adds cost. Reaming, boring, and grinding exist to tighten what a drill cannot hold, so the question on any drawing is which of those steps the tolerance calls for.

Why does a drilled hole rarely hold the tolerance on the drawing?

A drill sets the approximate size and position of a hole, not its final tolerance. The finished diameter depends on the drill, the runout in the setup, and the material being cut, and a drilled hole can come out slightly oversize, tapered, or off straight. For holes that only need to clear a fastener, that is fine, and the drill does the job, typically at the lowest cost.

The trouble starts when a drawing puts a tight size tolerance on a hole that would otherwise only be drilled. The shop then has two choices: add a finishing operation or ask about the callout. Either way the quote changes, which is why it helps to decide early which holes need a tolerance and which only need a size.

When does a hole need reaming?

A hole needs reaming when the drilled size is not close enough and the hole is already straight and in the right place. A reamer is a multi-point cutting tool that finishes a drilled hole to size by removing a small amount of stock. According to Cutting Tool Engineering, a reamer follows the existing hole instead of correcting it, and it is more often used to hit a diameter than to produce a fine surface finish.

That is why the drilled hole has to be good before the reamer starts, and why shops leave a small, controlled amount of stock for it. One toolmaker quoted in the same article gives a rule of thumb of 0.010 to 0.015 inch after drilling, with less for very small diameters. When too much stock remains, the options include reaming twice or switching to a different tool.

Reaming typically gives a quicker cycle time than boring, which often makes it the economical choice when the hole is already straight.

When does boring beat reaming?

Boring beats reaming when the hole’s location, straightness, or diameter needs correction. A boring tool cuts its own path instead of following the drilled hole, so it can move the center of a hole, remove a taper, and bring the hole to size. The same Cutting Tool Engineering article recommends boring when the hole shape or location needs correction.

Boring can also suit smaller quantities, since an adjustable boring head can finish a range of diameters without a dedicated reamer for each size. The trade is speed, because boring typically takes longer per hole than reaming. Both processes can hold tight diameters on a well-prepared hole, so the choice usually comes down to correction needs, quantity, and cost.

What tolerance does each process make realistic?

Published figures vary with the tool, the material, and the machine, so a single tolerance number does not transfer between shops. The table below compares what each process controls and where it stops, and it leaves the numbers to the shop that will cut your part.

Process What it controls Where it stops Cost direction
Drilled Approximate size and position Size, roundness, and straightness vary with the drill and the setup Typically lowest cost
Reamed Final size on a hole that is already straight Does not correct location or straightness Quicker than boring
Bored Size, straightness, and location Typically slower per hole than reaming Can suit small lots
Ground Very tight size, roundness, and finish requirements Used when the other three cannot hold the callout Adds a further operation

When drilling, reaming, and boring cannot hold a callout, grinding takes over, and the OD, ID, and surface grinding guide explains how.

A hole’s depth and diameter set the process before the tolerance does

Depth narrows the options before the tolerance is even considered. A published design guide recommends limiting hole depth to about four times the diameter, and says deeper holes, up to about ten times the diameter, are possible but cost more because of longer machining time. The same guide notes that through holes are easier to machine than blind holes, so a through hole is the better choice when the function allows.

A deep, small hole can also limit the finishing tool, since the tool has to reach the full depth with enough rigidity to stay on size. That is why a tolerance that is easy on a shallow hole can call for a different process on a deep one.

Tolerance only the holes that mate

Every tight hole tolerance can add an operation, so it pays to separate the holes that must fit something from the holes that only need to exist. A hole that receives a pin, a bearing, or a shaft earns a size tolerance. A hole that passes a bolt does not. On a drawing with twelve clearance holes and two dowel holes, only the two dowel holes need the tight callout, and the other twelve can be drilled. The tight tolerance machining guide covers machining to tight tolerances in more depth.

Position between holes is a separate callout from size. A bolt pattern that must line up with a mating part depends on hole location, not just diameter, and the GD&T guide for buyers explains how position tolerances work.

How is a hole tolerance written on a drawing?

A hole tolerance can be written as a plus-and-minus value on the diameter or as an ISO 286 fit class such as H7. A fit class packs the limits into a letter and a number instead of two values. According to High-Performance Composites, the hole-basis system in ISO 286 has four preferred hole tolerances, H11, H9, H8, and H7, and the smaller the number, the more precise the hole.

Either form works. If the drawing uses a fit class, confirm with the shop that it is the form they expect to quote from.

What should the drawing say about each hole?

A hole callout that states size, tolerance, depth, and finish lets the shop pick the process without guessing. These are the items that matter most:

  • Diameter and size tolerance, written as plus-minus or an ISO fit class, with a tolerance only on holes that mate
  • Depth, and whether the hole is through or blind
  • Surface finish, only where the function needs it
  • Position, with the datums the holes are located from
  • Thread callout and thread depth, if the hole is tapped
  • Material and quantity, since both influence whether a shop reams or bores

Send the drawing with those details and request a quote through the quote form. The design for CNC milling guide covers pockets and walls that sit near holes, and the precision CNC machining services page lists the processes FM Machine Co. offers.